Page 279 - ZSi-Foster Product Catalog

Concrete Inserts

Standard Finish: Pre-Galvanized (PG)
5
5
Concrete Inserts - 1 ⁄8" x 1 ⁄8" - 12 Gauge
When ordering specify finish. Available in plain, pre-galvanized, hot dip W5952 Introduction
galvanized after fabrication, type 304 and 316 stainless steel. Stainless steel
sizes with Anchor end caps, the end caps will be hot dip galvanized
Refer to page 278 for continuous concrete insert part number selection chart to
build complete part number based on desired options. 3 ⁄8"
1
79mm Channel
Safe Uniform
FLORIDA STRUT VERSABAR  WESANCO Size Load per L.F. † Size
Lbs. (kN)
VC1003 3" (76mm) Channel Nuts & Hardware
W7250 -- W7250 4" (102mm) 800 (3.56 kN)
W7251 VC1006 W7251 6" (152mm) 1000 (4.45 kN)
W7252 -- W7252 8" (203mm) 1200 (5.34 kN) 3 ⁄4"
VC1009 9" (229mm) 19mm
W7253 * VC1012 W7253 * 12" (305mm) General Fittings
3
W7254 -- W7254 16" (406mm) 1 ⁄8"
-- VC1018 -- 18" (457mm) 35mm
W7255 -- W7255 20" (508mm)
W7256 VC1024 W7256 24" (610mm) Brackets
5
VC1030 30" (762mm) 1 ⁄8"
W7257 -- W7257 32" (813mm) 41mm
W7257A VC1036 W7257A 36" (914mm)
W7258 -- W7258 40" (1016mm) 1 ⁄8" Beam Clamps
5
-- VC1042 -- 3' - 6" (1.1m) 41mm
W7259 VC1048 W7259 4' - 0" (1.2m)
-- VC1054 -- 4' - 6" (1.4m)
W7260 VC1060 W7260 5' - 0" (1.5m)
13 ⁄16"
-- VC1066 -- 5' - 6" (1.7m) 21mm Pipe & Conduit Supports
2000
W7261 VC1072 W7261 6' - 0" (1.8m) (8.90 kN)
-- VC1078 -- 6' - 6" (2.0m)
W7262 VC1084 W7262 7' - 0" (2.1m) 1 ⁄2"
1
-- VC1090 -- 7' - 6" (2.3m) 38mm
W7263 VC1096 W7263 8' - 0" (2.4m) 3 ⁄8" Electrical Fittings
1
-- VC1102 -- 8' - 6" (2.6m) 79mm
W7264 VC1108 W7264 9' - 0" (2.7m) 1 ⁄8"
5
-- VC1114 -- 9' - 6" (2.9m) 41mm
W7265 VC1120 W7265 10' - 0" (3.0m) Spring Steel
W7266 VC1144 W7266 12' - 0"(3.6m) 5
1 ⁄8"
W7267 VC1168 W7267 14' - 0" (4.2m) 41mm
W7268 VC1192 W7268 16' - 0" (4.8m)
W7269 VC1216 W7269 18' - 0" (5.4m) Concrete Inserts
W7270 VC1240 W7270 20' - 0" (6.1m) Concentrated load on the end 2" (51mm) of W7252
-- VC1288 -- 24' - 0" (7.3m) thru W7270 should not exceed 1000#. Inserts must be
* W7253 utilizes tab channel (punched & anchor caps) surrounded by sufficient concrete to conform to design
† Embedded in 3,000 psi or better concrete, Safety Factor = 3 shear stress. Concrete insert should be nailed to form
 Versabar dimensions are different every 16" to 24" (406mm to 635mm) Rooftop Supports

Technical Data

Hole Diameter: ⁄16" (14mm); Hole Spacing - From End: ⁄16" (21mm); Hole Spacing - On Center: 1- ⁄8" (48mm); Width: 1- ⁄8"(41mm); Thickness: ⁄4" (6mm)
1
13
9
5
7
www.zsi-foster.com – 279 –
WARNING: Cancer and Reproductive Harm Warning. For more information go to www.P65Warnings.ca.gov.